|
| |
|
DOOR SPECIFICATIONS |
|
 |
Product: The court door units as shown on plans and
specifications shall be CRS Products International door as manufactures by CRS Products
International 150 Gate 5 Road, Suite 204, Sausalito, California, U.S.A. 94965 Telephone
(415) 543-4113 Fax (415) 332-0818 Toll Free 1-800-661-4174 10021 - 169 Street,
Edmonton, Alta., Canada T5p 4M9 (780) 484-2786 Fax (780) 484-5827 419 Avon Crescent,
Oakville, Ont., Canada L6J 2T1 Telephone (416) 283-3452 Fax (416) 283-3452. Door units to
be specified by model number and swing direction. Units shall be completely prehung,
finished with all necessary hardware attached and properly packaged ready for
installation.
Components: FRAME and THRESHOLD shall be 32 mm (1 1/4") x 152 mm (6") in prefinished white with rabbeted and screwed corner joints.
DOOR shall be CRS 12.7 mm (1/2") clear tempered glass with polished edges and white lines.
HARDWARE: HINGES shall be side hinges of poly- urethane plastic in black,
premounted to doorlite and frame.
DOOR STOP and LATCH KEEPER shall be black poly- urethane plastic premounted
to wood frame. White fittings available upon request.
DOOR LATCH shall be comprised of black poly- urethane plastic casing
with brushed aluminum cover. Opening mechanism shall be conventional turn knob outside
with chromed flush ring door pull on inside, premounted to frame. |
Installation: Prefinished Wood Frame Door shall be installed as
per manufacturer's written instructions included with the unit. Court side of the door
unit to be flush with the playing surface. LIGHTING & COLOR INFORMATION
CLEAR GLASS
Where clear glass walls are to be installed, care must be given to provide
proper play. Interior court lighting can be any industry acceptable lighting manufacturer.
On the exterior side and close to the glass wall, care must be taken to have light levels
equal or nearly equal to the interior foot candle level - a light ratio of more than 2 to
1, interior to exterior, will cause unwanted reflections on the interior glass surface.
Exterior floor finishes near clear glass walls must be light in color within
three feet of the glass. Beige, bright orange, etc., or the extension of the court wood
floor 2438 mm (8')± would be
recommended. Dark colors, i.e., brown, dark gray, etc. cause backgrounds against which
view of the ball can be lost through the glass.
LIGHTING
SYSTEMS INFORMATION AVAILABLE UPON REQUEST
|
CRS PRODUCTS INTERNATIONAL 12.7 MM (1/2") TEMPERED
GLASSWALL SPECIFICATIONS |
Part
I - Scope
1.1 Provide all labor,
equipment, material to finish and completely install the glass walls, glass doors, and
court windows including glass and hardware where called for on drawings.
Part II - Materials
2.1 MANUFACTURER - CRS Products International Glasswall Systems. 150 Gate 5 Road,
Suite 204, Sausalito, California, U.S.A. 94965 Telephone (415) 543-4113 Fax (415) 332-0818
Toll Free 1-800-661-4174 10021 - 169 Street, Edmonton, Alta., Canada T5P 4M9 (780)
484-2786 Fax (780) 484-5827 419 Avon Crescent, Oakville, Ont., Canada L6J 2T1 Telephone
(416) 283-3452 Fax (416) 283-3452 Glass - 12.7
mm (1/2") clear float tempered with all
exposed edges polished. Conforming to Federal Specifications: DD-G-451C, DD-G-001403,
ANSIZ97.1 - 1975, CPSC 16 CFR 1201.
Heat soaked glass available upon request.
2.2 GLASS-TO-GLASS CONNECTIONS
All hardware for glass-to-glass connections shall be Hi-Tensile ML Black Nylon with a
tensile strength of 9,000 to 12,000 psi and a Durometer hardness of D80-90. White fittings
available upon request. Metal fittings mounted on the glass shall not be acceptable.
DOOR HARDWARE - Door shall be locked by means of a positive locking system with a
lever-set on the exterior and flush ring pull on the interior. Lock housing to be clear
anodized finish. Finger hole in door to actuate lever on exterior door is not acceptable. |
2.3 DOORS - Doors shall be 2134 mm (7') tall and must be side hinged.
2.4 PERIMETER CHANNELS - Clear anodized aluminum.
2.5 FIN BRACKETS - Fin brackets shal be steel with clear anodized
aluminum cover plates or silver chrome plated or 24 karat gold plated.
2.6 JOINT SEALANT - GE. 1200 pr equal
2.7 GLASS MARKINGS
A. Rear glass walls shal have CRS "ULTRA-VUE" coating for all court
glass where specified on the plans by covering the glass with white dots consisting of 16
lines per inch ceramic frit dot screen, with 50% opaque coverage to the court side surface
of the glass. "ULTRA-VUE" is designed for optimal playability providing players
with superior depth perception and increased ball visibility. Descrete defects or
checkerboard efect pattern will not be accepted.
ULTRA-VUE - Is "burned" permanently into the surface of the glass during the
tempering process, providing a consistant surface that ensures desirable ball behaviour.
Sytems utilizing applied glue on products to either the interior or exterior surfaces of
the glass are unacceptable.
B. All rear walls are to have white etched or snadblasted lines 25 mm (1") om center for 610 mm (24") or 762 mm (30") in height with a thickness
of approximately 3 mm (1/8").
Such markings are to permanent. |
C.
White logos are available sandblasted or etched. Specify if required.
PART III - PERFORMANCE
3.1 Walls may deflect under impact of players if it is necessary to do so. Limits
of deflection are as folloes with the equivalent impct of a 200 lb. man moving at 3048 mm (10') per
second with a normal coefficient of absorption of 47%.
A. 1 1/4" for glass walls at the center of impact.
B. For doors, the glass thickness plus 3 mm (1/8") at an impact
velocity of 3048 mm (10') per second or the thickness of glass plus 12.7 mm (1/2")
at 4572 mm (15') per second.
3.2 Install walls, doors, and related work as specified and as deatiled
on the drawings using experienced workmen. Set walls plumb, level, square and true and
securely anchored in place, with all joints siliconed smooth. Provide all anchors, clips,
fastenerd and accessories for complete installation.
PART IV - WARRANTY
4.1 All glass walls shall be structurally sound and free from defects in material
and workmanship under normal use and service for a period of five (5) years after the date
of delivery of the wall and fixtures to the purchaser. |
|
Specifications subject to change. |
|
| "THE MOST INNOVATIVE SYSTEMS AVAILABLE IN THE WORLD
TODAY!" |
CRS PRODUCTS
INTERNATIONAL
150 GATE 5 ROAD, SUITE 204
SAUSALITO, CALIFORNIA,
U.S.A 94965
TELEPHONE (415)543-4113
FAX (415) 332-0818
TOLL FREE 1-800-661-4174 |
CRS PRODUCTS INTERNATIONAL
10021 - 169 STREET
EDMONTON, ALTA.,
CANADA T5P 4M9
TELEPHONE (780) 484-2786
FAX (780) 484-5827 |
CRS PRODUCTS
INTERNATIONAL
419 AVON CRESENT
OAKVILE, ONT.,
CANADA L6J 2T1
TELEPHONE (416) 283-3452
FAX (416) 283-3452 |
CRS PRODUCTS
INTERNATIONAL
UNIT #1, 3511 VIKING WAY
RICHMOND, B.C.,
CANADA V6V 1W1
TELEPHONE (604) 278-7997
FAX (604) 278-7967 |
|
